SpeedNeeds Diagnostics Index

Free Tools & Calculators

Every open calculator and tool on SpeedNeeds — no account, no cost. Grouped by the job in front of you, and every card is badged FREE because every one of them is.

Tools Library  ·  Command Center

97Open tools & calculators
6Job groups
$0No account, no cost

No-start & electrical proof

Voltage drop, ignition, and the checks that prove whether the circuit and the spark are doing their job.

ToolFREE
Dwell Time CalculatorThis tool estimates dwell limits by RPM based on time per spark event, coil saturation time, and voltage. It helps you spot where dwell collapses and misfire shows up first. No...
ToolFREE
Dwell Window CalculatorPick your ignition architecture, cylinders, and RPM — the calculator works out how much charge time each coil actually gets per firing and tells you if the coil can fully charge or if the window is gone before the dwell is done.
ToolFREE
Timing Scatter EstimatorTiming scatter is how much the actual spark timing jitters around the commanded value. This tool estimates scatter from common mechanical and signal contributors: distributor...
ToolFREE
Ignition Command Logic MapperDecision-support pre-test tool that maps who is allowed to create spark under the current condition.
ToolFREE
Ignition Cutout Pattern Identifier v1.2.1Identify likely ignition cutout categories from observed patterns (tach behavior, duration, load/heat dependency, recovery, and warning signs). Decision-support only.
ToolFREE
Ignition Keep-Alive / Run-On Fault IdentifierPost-test pattern matcher that flags the most likely ignition keep-alive/run-on fault class from simple yes/no observations.
ToolFREE
Relay Backfeed / Latch Fault IdentifierPost-test pattern matcher that flags the most likely relay latch/backfeed fault class from simple yes/no observations.
ToolFREE
Spark Plug Gap vs Cylinder Pressure ToolThis tool recommends a plug gap range based on a simple cylinder pressure factor. Higher pressure needs a tighter gap. Use this to stop guessing when boost, nitrous, or...

Fuel system sizing

Injector size, pump sizing, BSFC, E85, and pressure — size the system to the power you are actually making.

ToolFREE
Boost Referenced Fuel Pressure Calculator V1Shows how boost raises rail pressure, reduces pump headroom, and changes injector differential pressure.
ToolFREE
Bsfc Fuel Demand Estimator V1Estimate total fuel mass required from horsepower and BSFC. This is system demand — pumps, injectors, and lines all key off this number.
ToolFREE
E85 Blend Calculator (Tank Math)Tank math only: calculate how many gallons of pump E85 and gasoline to add to reach a target ethanol percentage. Includes validation & reality checks.
ToolFREE
Fuel Injector Size CalculatorCompute required injector size from power, BSFC, injector count, duty cycle, and fuel pressure — or estimate supported HP from injector size. Shows lb/hr and cc/min with fuel density and pressure scaling.
ToolFREE
Fuel Pump Sizing CalculatorSize your fuel pump(s) from horsepower, BSFC, fuel type density, pump count, and max pump duty. Outputs total fuel demand and recommended pump rating per pump in GPH and LPH.
ToolFREE
AFR Target Builder (Use Case)Idle, cruise, and WOT AFR targets by induction, fuel, and vehicle use — with lambda conversion and safety notes.
ToolFREE
E85 Stoich & Fueling MultiplierCalculate blend stoich AFR from ethanol content and gasoline stoich, plus fueling multiplier and injector/pump percent increase vs gasoline.
ToolFREE
Excessive Fuel Pressure Classifier v1.0Compare measured rail pressure to base spec and user tolerance to classify overpressure patterns for fuel pressure regulation diagnostics.
ToolFREE
Fuel Pressure Snapshot Logger (Prime/Crank/Run + Hold)Log fuel pressure at prime, crank, run, and hold. Includes a user-started hold timer and printable notes.
ToolFREE
Fuel Pump Command Logic MapperDecision-support pre-test tool that maps who is allowed to command the fuel pump under the current condition.
ToolFREE
Injector Command Logic MapperDecision-support pre-test tool that maps who is allowed to pulse injectors under the current condition.
ToolFREE
Injector Duty Cycle and Pulsewidth Reality CheckPrevents WOT peg, crappy idle, and data-limited tunes by showing what your injectors can actually do per cycle.
ToolFREE
Injector Flow Rate (lb/hr vs cc/min) ToolConvert injector flow between lb/hr and cc/min with fuel density and optional pressure scaling. SpeedNeeds Tool.
ToolFREE
Injector Voltage Drop LoggerStandalone SpeedNeeds Injector Voltage Drop Logger for recording injector feed voltage and drop across multiple injectors.
ToolFREE
Prime vs Hold Pressure Comparator v1.0Compare prime peak, crank, running pressure, and post-shutdown hold to interpret fuel control/containment patterns without guesswork.
ToolFREE
Residual Fuel Pressure Decay Tool v1.0Residual Fuel Pressure Decay Tool v1.0 - capture rail pressure vs time after shutdown and interpret decay patterns.

Air & boost

Airflow, carb and throttle-body sizing, MAF capacity, and intake math for NA and boosted combos.

Gearing, speed & RPM

Tire, gear, speedometer, and RPM math — what the combination actually does on the road.

Engine & build math

Displacement, camshaft sizing, torque and horsepower, suspension setup, and project budget math.

ToolFREE
Camshaft SizerSize a cam to the combo you already have. Pick the use, heads, intake, rear gear, transmission, and the idle you want. Get a duration range at .050, a lobe separation range, and the checks to run before you buy. No part numbers.
ToolFREE
Compression Ratio CalculatorStatic and dynamic compression ratio from bore, stroke, chamber volume, head gasket, deck height, and piston dome or dish. Every part of the clearance volume itemized in cc, displacement in CID and liters, and a solve-for-a-target mode.
ToolFREE
Engine Displacement Calculator (CID & Liters)Compute engine displacement from bore, stroke, and cylinder count. Inches or millimeters in, CID/cc/L out. SpeedNeeds tool UI (Calculate → Reset → Load Example).
ToolFREE
Roll Stiffness Balance Estimator (v1)Estimate front vs rear roll stiffness balance from springs, motion ratio, and sway bars. Explains push vs loose with safe adjustment suggestions.
ToolFREE
Spring Rate vs Corner Weight (Calculator + Sanity Checker)Estimate spring rate from corner weight, motion ratio, and a target ride frequency or wheel rate. Includes wheel rate, ride frequency, and sanity flags.
ToolFREE
Torque ⇄ Horsepower ConverterConvert torque to horsepower (and back) at any RPM. Button-driven only, with plain-English explanations.
ToolFREE
Project Car Budget TriageFigure out whether the project makes sense before the parts pile eats the budget. Identify the biggest blockers, set a realistic ceiling, and choose the next three moves you can actually finish.
WorksheetFREE
Project Car Purchase Decision WorksheetShould you buy this project car? A free SpeedNeeds worksheet that proves what you're actually buying before you drag it home — paperwork, condition, money math, and the final call.
ToolFREE
Shock Travel & Bottoming CheckerSafety-focused suspension tool to check bump/droop travel, shock limits, bump stop engagement, and bottoming risk. Manual-calc only.

Worksheets, logs & checklists

Printable and screen-use worksheets, capture logs, and checklists for structured proof capture.

WorksheetFREE
Battery Internal Resistance Crank-Sag WorksheetSpeedNeeds worksheet for proving battery internal resistance during cranking from steady-state, time-correlated voltage sag and total current — with rating-scaled bands, two-event agreement, and honest verdict boundaries.
WorksheetFREE
Battery State-of-Charge Log WorksheetProve a battery's state of charge before cranking tests mean anything — battery and measurement-method lock, sanctioned surface-charge removal with disclosed bias directions, post-to-post rest-voltage log against the chemistry's OCV map with the 75% adequacy bar, hydrometer corroboration with a 0.05
WorksheetFREE
Before-After Diagnostic Capture WorksheetSpeedNeeds worksheet for recording symptom state before and after one controlled diagnostic change so masking, resets, heat, load, and setup drift do not fake a fix.
WorksheetFREE
Cam/Crank Correlation Evidence Log WorksheetProve what is behind a proved cam/crank correlation failure — freshness and SI correlation-rule lock, crank- and cam-signal content screens at the controller input, phase-offset judgment against the SI window across two independent sightings, the VVT park test, and an honest correlation verdict.
WorksheetFREE
Click-Pattern Capture Log WorksheetSpeedNeeds worksheet for a repeated-clicking no-crank complaint: lock the click event and burst discipline, capture rest voltage against the 12.4 V gate, click-event burst MINs at the posts against the temperature-adjusted floor, leg peak drops with subdivision readings, S-terminal MIN with the diff
WorksheetFREE
CMP Capture Log WorksheetLog the camshaft position signal's electrical path — CMP design, SI-identified test points, recorded SI requirements, scope settings, and source-vs-controller-input capture log with check-period notes; the verdict is the mechanic's, with the boundary printed on it ("proves the path — never the senso
WorksheetFREE
Coil Feed Voltage-Drop Log WorksheetSpeedNeeds worksheet for proving ignition-coil feed voltage loss under real circuit load, isolating the affected feed segment, and documenting before-and-after repair results.
WorksheetFREE
Coil Output Test Log WorksheetLog ignition-coil secondary output at the problem condition — method, gap, and measurement-point lock, suspect-vs-known-good capture log with load-isolation confirmation, and an honest output verdict.
WorksheetFREE
Coil Power Capture Log WorksheetLog the coil primary power evidence gate by gate — KOEO presence, sustained-crank battery, current demonstration, differential MAX on both cranks, stability watch, and the source record.
WorksheetFREE
Crank-No-Start Evidence Capture WorksheetA SpeedNeeds diagnostic worksheet for capturing cranking state, combustion evidence, RPM and synchronization clues, fuel and ignition findings, power and ground condition, and the next controlled test during crank-no-start diagnosis.
WorksheetFREE
Crank-No-Start First-Split Capture Log WorksheetSpeedNeeds worksheet for a crank-no-start complaint at normal crank speed: lock the condition, capture the security-indicator state, the prime-listen result with fuse and inertia-switch state, spark delivery to the tested boot, rail pressure during crank against the SI spec, injector command on two
WorksheetFREE
Crank-Signal Capture Log WorksheetProve the crankshaft-position signal at the problem cranking condition — circuit-identity and method lock, source-side vs controller-input capture log with check-period requirements (SI vs screening authority) and scan-RPM corroboration, and an honest crank-signal verdict.
WorksheetFREE
Crank-to-RUN Transition Capture WorksheetA SpeedNeeds diagnostic worksheet for recording catch/no-catch behavior, key-release behavior, observation method, and evidence quality during crank-to-RUN transition checks.
ChecklistFREE
Cross-System Influence ChecklistA SpeedNeeds diagnostic checklist for naming load, heat, reset, bypass, repair state, module state, power/ground, and modification influences before continuing diagnosis.
WorksheetFREE
Direct Symptom Proof Capture WorksheetSpeedNeeds worksheet for capturing complaint, locked condition, selected affected system, observation method, evidence quality, and the next controlled diagnostic test.
WorksheetFREE
Dropout Capture Log WorksheetLog intermittent sensor-circuit dropout evidence — method lock, provocation pass log with tool and capture window, return-to-baseline discipline, per-pass leg hypothesis, and matched retest. One pass is suspicion, never a verdict.
WorksheetFREE
Evidence Inventory and Fault Grouping HelperSpeedNeeds worksheet for separating symptoms, codes, warnings, failed checks, verified observations, reported-only observations, condition locks, and leftover evidence before choosing a diagnostic path.
WorksheetFREE
Fuel Pressure Capture Log WorksheetSpeedNeeds worksheet for a low fuel pressure complaint: prove the gauge reading is real first, capture KOEO prime behavior, idle and load pressures against the SI spec, prove pump voltage at the pump connector before any parts call, record regulator rise, and time the residual leakdown — then pick t
WorksheetFREE
Fuel Pump Prime Observation Log WorksheetProve the key-on fuel pump prime command at the relay output — relay ID and setup lock, prime-window capture log with same-window feed-vs-output comparison, key-off backfeed and never-terminates screens, relay swap subdivision, and the prime-command verdict with its boundary printed.
WorksheetFREE
Fuse Contact Test Log WorksheetA fuse that looks perfect can still starve its circuit — this worksheet walks a loaded fuse-contact test end to end: lock the fuse and its mapped load, log loaded millivolts at every subdivision point, auto-compute interface resistance (mV ÷ A = mΩ), isolate the failed sub-element with swap and prov
WorksheetFREE
Ground-Map Capture WorksheetSpeedNeeds worksheet for mapping ground-point voltage rise through two controlled load steps, recording minimum and maximum excursions, and documenting every unmeasured point.
WorksheetFREE
Hot-Event Fuel Capture WorksheetSpeedNeeds proof-first worksheet for correlating hot-event temperature, fuel pressure, command, voltage, timing, and symptom behavior under controlled conditions.
WorksheetFREE
Ignition Switch START Output Log WorksheetProve the ignition switch START output at the switch terminal — topology and method lock (relay-driven lamp-loaded / solenoid-direct live-attempt / module-mediated), SI wire identity with the 150–400 mA lamp discipline, loaded feed + output capture with the direct across-contact drop, hot-only-in-ST
WorksheetFREE
Interlock Switch Test Log WorksheetSpeedNeeds worksheet for proving the neutral safety / clutch interlock switch at its own terminals — input/output voltage during a live crank request, Park-vs-Neutral repeat, starter-disabled inverse safety test, and one bounded adjustment attempt.
WorksheetFREE
Intermittent No-Crank Capture Log WorksheetCatch the no-crank or slow-crank that only happens sometimes — condition-lock interview with written when/what, per-occurrence pattern log with failing-now routing hints, static inspection + crimp-flex, twice-reproduced key-on provocation record measured across the joint itself, a two-tier capture k
WorksheetFREE
Key-Cycle Before/After Comparison WorksheetSpeedNeeds worksheet for comparing an active symptom before key-off, the immediate restart response, and a later comparable-condition recheck without mistaking temporary recovery for a repair.
WorksheetFREE
Key-Cycle Symptom Baseline Capture WorksheetSpeedNeeds worksheet for capturing the active symptom, warning state, operating conditions, and exact key-off intervention before a key-cycle recovery test.
WorksheetFREE
Loaded Fuel Delta-P WorksheetRecord the loaded fuel filter restriction test — filter inlet and rail pressure captured under the same pull, with the sheet computing the delta-P against the service-information limit on every pull and checking the two-pull agreement. The sheet computes the math; you own the verdict.
WorksheetFREE
Loaded Return-Side WorksheetRecord the loaded return-side fuel test: the rated-hold spec from service information, stock pulls vs free-return pulls in A-B-B-A order, and rail PSI at idle and load per pull. The sheet computes regulator tracking, hold-vs-spec bands, repeat agreement, and the pull-to-pull separation that splits r
WorksheetFREE
Module Output Capture Log WorksheetLog the module driver output evidence card by card - pin ID, command state, supply and ground under load, output voltage no-load and loaded with current demonstrated, and the load-terminal proof. The sheet computes the loaded vs no-load collapse delta; you own the verdict.
ChecklistFREE
Multi-Code Cluster SorterSpeedNeeds Multi-Code Cluster Sorter for sorting stored, pending, history, and permanent codes into shared-source versus system-specific clusters.
WorksheetFREE
No-Crank First-Split WorksheetSpeedNeeds worksheet for safely capturing START observation, starter response, engine rotation evidence, abnormal clues, and the correct first no-crank routing branch.
WorksheetFREE
Parked Fluid Spot Evidence LoggerSpeedNeeds worksheet for recording parked fluid spot freshness, repeatability, vehicle-relative location, odor, color, surface conditions, and wettest-point tracing before classifying a leak.
WorksheetFREE
Project Car Budget TriagePut the build in the right order before the parts pile eats the budget. Identify what blocks progress, price the real work, and choose the next seven jobs you can actually finish.
WorksheetFREE
Recent Service / Reset Intake WorksheetSpeedNeeds worksheet for capturing battery disconnect, jump-start, code clearing, programming, calibration, collision, water intrusion, and aftermarket electrical context before warning-light routing.
WorksheetFREE
Reference-Integrity WorksheetSpeedNeeds worksheet for auditing fuel-pressure regulator reference integrity with source-locked specifications, B5 verification, idle vacuum and disconnect-rise math, hand-pump tracking, nipple checks, boost comparison readings, observations, and prior verdict capture.
WorksheetFREE
Relay-Hold WorksheetSpeedNeeds worksheet for proving relay terminal identity, command state, coil/control behavior, and load-side output while a relay is commanded to pull in and remain energized.
WorksheetFREE
Repeat Spot Classification ChecklistA SpeedNeeds diagnostic worksheet for classifying a repeated parked-fluid mark as an active leak, residue, or insufficient evidence using controlled recheck conditions.
WorksheetFREE
Return-Line Restriction WorksheetSpeedNeeds worksheet for proving and locating fuel return-line restriction using platform specifications, KOEO, idle and load pressure readings, controlled pinch and vacuum-reference responses, and return-path vent testing.
WorksheetFREE
Returnless Demand-Step Capture WorksheetSpeedNeeds worksheet for capturing synchronized returnless fuel-system pressure, pump command, electrical supply, and engine-demand readings through a transient demand step.
WorksheetFREE
Returnless pressure control: why the dip is not automatically a weak pumpWhy a momentary rail-pressure dip after a demand step can be control-loop lag instead of a weak pump, and how to prove which one you are looking at.
ChecklistFREE
Safe-Stop Decision Helper v01SpeedNeeds Safe-Stop Decision Helper for broad active-warning and no-drive decision support before normal QTS routing.
WorksheetFREE
Segment Isolation Walk Log WorksheetWalk a circuit one segment at a time and log it in test order — walk boundaries, readings at each boundary, and current-signature checks — with per-segment differentials computed, so the fault's home segment is proved and the path can be retraced.
WorksheetFREE
Slow-Crank Capture Log WorksheetSpeedNeeds worksheet for a slow-crank complaint: lock the battery condition, capture steady cranking voltage against a temperature-adjusted floor, run the draw guard, split per-leg voltage drop during crank, measure starter terminal voltage direct, and screen starter draw — then pick the verdict you
WorksheetFREE
START-EVENT CAPTURE LOG WORKSHEETProve the ignition feed in START at the scoped test point — circuit-design and setup lock, same-event source and feed capture log with the repeat gate, instability record, interpreted-input state check, and the START-feed verdict with its boundary.
ChecklistFREE
Start-to-Run Observation ChecklistA SpeedNeeds diagnostic checklist for capturing key release, catch/run duration, throttle-assist response, security and warning indicator state, and unsafe evidence during immediate post-start run-loss classification.
WorksheetFREE
Starter Current Draw Capture Log WorksheetA slow crank with a good circuit means the starter motor itself is suspect — but crank speed is not a measurement. This worksheet logs two sustained, zero-corrected cranking-current captures against a stated reference (SI max spec, known-good, or the default band), locks the clamp/battery/circuit co
WorksheetFREE
Starting-System Voltage-Drop WorksheetSpeedNeeds worksheet for recording loaded starting-system voltage drop, crank voltage, cable loss, ground loss, terminal/contact loss, and starter response evidence before condemning parts.
WorksheetFREE
Symptom Reproduction WorksheetSpeedNeeds worksheet for capturing complaint condition, reproduced condition, repeatability, safety, and observation quality before diagnostic routing.

Related Tool

Get new drops in your inbox

Read the Privacy Policy.