SpeedNeeds Diagnostics Index

Diagnostic Capture Logs

The capture-log and evidence-log worksheets, pulled out of the full worksheets library onto one page. For the rest of the library, go to the Diagnostic Worksheets page.

Command Center / Tools Library

Search

Capture Logs and Evidence Logs

WorksheetFREE
Before-After Diagnostic Capture Worksheet Diagnostics tools/worksheets/before-after-diagnostic-capture-worksheet.html
SpeedNeeds worksheet for recording symptom state before and after one controlled diagnostic change so masking, resets, heat, load, and setup drift do not fake a fix.
ToolFREE
Cam/Crank Correlation Evidence Log Worksheet Prove what is behind a proved cam/crank correlation failure — freshness and SI correlation-rule lock, crank- and cam-signal content screens at the controller input, phase-offset judgment against the SI window across two independent sightings, the VVT park test, and an honest correlation verdict.
ToolFREE
Click-Pattern Capture Log Worksheet SpeedNeeds worksheet for a repeated-clicking no-crank complaint: lock the click event and burst discipline, capture rest voltage against the 12.4 V gate, click-event burst MINs at the posts against the temperature-adjusted floor, leg peak drops with subdivision readings, S-terminal MIN with the differential check, and post-burst recovery — then pick the verdict your evidence supports.
ToolFREE
CMP Capture Log Worksheet Log the camshaft position signal's electrical path — CMP design, SI-identified test points, recorded SI requirements, scope settings, and source-vs-controller-input capture log with check-period notes; the verdict is the mechanic's, with the boundary printed on it ("proves the path — never the sensor, never the correlation").
ToolFREE
Coil Power Capture Log Worksheet Log the coil primary power evidence gate by gate — KOEO presence, sustained-crank battery, current demonstration, differential MAX on both cranks, stability watch, and the source record.
WorksheetFREE
Crank-No-Start Evidence Capture Worksheet tools/worksheets/crank-no-start-evidence-capture-worksheet.html
A SpeedNeeds diagnostic worksheet for capturing cranking state, combustion evidence, RPM and synchronization clues, fuel and ignition findings, power and ground condition, and the next controlled test during crank-no-start diagnosis.
ToolFREE
Crank-No-Start First-Split Capture Log Worksheet SpeedNeeds worksheet for a crank-no-start complaint at normal crank speed: lock the condition, capture the security-indicator state, the prime-listen result with fuse and inertia-switch state, spark delivery to the tested boot, rail pressure during crank against the SI spec, injector command on two injectors, and crank rhythm — then pick the verdict your evidence supports.
ToolFREE
Crank-Signal Capture Log Worksheet Prove the crankshaft-position signal at the problem cranking condition — circuit-identity and method lock, source-side vs controller-input capture log with check-period requirements (SI vs screening authority) and scan-RPM corroboration, and an honest crank-signal verdict.
WorksheetFREE
Crank-to-RUN Transition Capture Worksheet tools/worksheets/crank-to-run-transition-capture-worksheet.html
A SpeedNeeds diagnostic worksheet for recording catch/no-catch behavior, key-release behavior, observation method, and evidence quality during crank-to-RUN transition checks.
WorksheetFREE
Direct Symptom Proof Capture Worksheet Diagnostics tools/worksheets/direct-symptom-proof-capture-worksheet.html
SpeedNeeds worksheet for capturing complaint, locked condition, selected affected system, observation method, evidence quality, and the next controlled diagnostic test.
ToolFREE
Dropout Capture Log Worksheet Log intermittent sensor-circuit dropout evidence — method lock, provocation pass log with tool and capture window, return-to-baseline discipline, per-pass leg hypothesis, and matched retest. One pass is suspicion, never a verdict.
ToolFREE
Fuel Pressure Capture Log Worksheet SpeedNeeds worksheet for a low fuel pressure complaint: prove the gauge reading is real first, capture KOEO prime behavior, idle and load pressures against the SI spec, prove pump voltage at the pump connector before any parts call, record regulator rise, and time the residual leakdown — then pick the verdict your evidence supports.
WorksheetFREE
Ground-Map Capture Worksheet Diagnostics tools/worksheets/ground-map-capture-worksheet.html
SpeedNeeds worksheet for mapping ground-point voltage rise through two controlled load steps, recording minimum and maximum excursions, and documenting every unmeasured point.
WorksheetFREE
Hot-Event Fuel Capture Worksheet Diagnostics tools/worksheets/hot-event-fuel-capture-worksheet.html
SpeedNeeds proof-first worksheet for correlating hot-event temperature, fuel pressure, command, voltage, timing, and symptom behavior under controlled conditions.
ToolFREE
Intermittent No-Crank Capture Log Worksheet Catch the no-crank or slow-crank that only happens sometimes — condition-lock interview with written when/what, per-occurrence pattern log with failing-now routing hints, static inspection + crimp-flex, twice-reproduced key-on provocation record measured across the joint itself, a two-tier capture kit for the next failure, and a watch-interval tracker that stays open until the evidence closes it.
WorksheetFREE
Key-Cycle Symptom Baseline Capture Worksheet tools/worksheets/key-cycle-symptom-baseline-capture-worksheet.html
SpeedNeeds worksheet for capturing the active symptom, warning state, operating conditions, and exact key-off intervention before a key-cycle recovery test.
ToolFREE
Module Output Capture Log Worksheet Log the module driver output evidence card by card - pin ID, command state, supply and ground under load, output voltage no-load and loaded with current demonstrated, and the load-terminal proof. The sheet computes the loaded vs no-load collapse delta; you own the verdict.
WorksheetFREE
Parked Fluid Spot Evidence Logger tools/worksheets/parked-fluid-spot-evidence-logger.html
SpeedNeeds worksheet for recording parked fluid spot freshness, repeatability, vehicle-relative location, odor, color, surface conditions, and wettest-point tracing before classifying a leak.
WorksheetFREE
Returnless Demand-Step Capture Worksheet Diagnostics tools/worksheets/returnless-demand-step-capture-worksheet.html
SpeedNeeds worksheet for capturing synchronized returnless fuel-system pressure, pump command, electrical supply, and engine-demand readings through a transient demand step.
ToolFREE
Segment Isolation Walk Log Worksheet Walk a circuit one segment at a time and log it in test order — walk boundaries, readings at each boundary, and current-signature checks — with per-segment differentials computed, so the fault's home segment is proved and the path can be retraced.
ToolFREE
Slow-Crank Capture Log Worksheet SpeedNeeds worksheet for a slow-crank complaint: lock the battery condition, capture steady cranking voltage against a temperature-adjusted floor, run the draw guard, split per-leg voltage drop during crank, measure starter terminal voltage direct, and screen starter draw — then pick the verdict your evidence supports.
ToolFREE
START-EVENT CAPTURE LOG WORKSHEET Prove the ignition feed in START at the scoped test point — circuit-design and setup lock, same-event source and feed capture log with the repeat gate, instability record, interpreted-input state check, and the START-feed verdict with its boundary.
ToolFREE
Starter Current Draw Capture Log Worksheet A slow crank with a good circuit means the starter motor itself is suspect — but crank speed is not a measurement. This worksheet logs two sustained, zero-corrected cranking-current captures against a stated reference (SI max spec, known-good, or the default band), locks the clamp/battery/circuit conditions first, and isolates a motor fault from engine mechanical resistance before any conclusion is drawn.