SpeedNeeds / Tool Bundles

Boost & Air Bundle

Match the boost to the engine before the boost costs you the engine.

Four SpeedNeeds tools for anything running boost: the turbo or the blower sized to the combination, what the intercooler is costing you, and the VE table the tune starts from.

Founding
$39
Regular
$69
One payment. No subscription. See the offer
Inside the Bundle01 / 03
The Turbo Compressor Map Helper after a run: 650 horsepower target, 12 psi of boost, and the verdict on screen, happy zone, with the pressure ratio and airflow worked out
Turbo Compressor Map Helper After the run: a 650 horsepower target, 12 psi of boost, and the verdict on screen, happy zone, with the pressure ratio and the airflow worked out.

01 / The problem

The most expensive guesses in the catalog.

Boost parts are the most expensive guesses in the catalog. A turbo bought too small chokes the top end. A turbo bought too big never spools where the car lives. A blower spun past its happy place makes heat instead of power, and heat is what lifts head gaskets and pulls timing. Then the car gets cranked up and does not pick up, and nobody can say whether the intercooler is eating the boost or the combination was never right.

Every one of those mistakes is visible in the numbers before a dollar moves. The airflow the engine needs, the pressure ratio the compressor will live at, the boost the intercooler throws away on the way to the manifold. Most builds never run them, because each one lives in a different corner of the catalog and nobody puts them in one place.

This bundle is that one place.

02 / How it works

Answers while the combination is still a plan.

Four tools, four questions. Is this turbo in its working range for your power and boost, or are you about to buy the wrong one? What will that pulley change actually give you, and is the blower still in its range? How much of your boost never reaches the manifold, and is the core big enough for the next pull? And when the tune starts, where does the VE table start from?

You get the answers on screen, while the combination is still a plan.

  • Is this turbo in its working range
  • How much of your boost never reaches the manifold
  • The VE table the tune starts from

03 / Inside

What’s inside.

Four tools, all of them in the bundle.

The four tools

  • Turbo Compressor Map Helper. a sanity checker, not a map replacement, and it says so. Give it your power target, boost, and elevation, and it works the airflow and pressure ratio against rough guardrails for the compressor family you pick, single or twin. Its job is to tell you when you are about to buy the wrong turbo.
  • Blower Drive Ratio & Air Demand. pulley sizes in, answers out. Drive ratio, blower rpm at your redline, pressure ratio, and estimated boost, with the engine’s air demand set against what the blower can supply, and warnings when the blower is oversped or into the heat zone. Roots, twin screw, and TVS presets are built in.
  • Intercooler Flow & Pressure Drop. estimates the pressure drop across your core and the heat soak risk, from your airflow demand and the core’s size, type, and quality. It sizes the core against the goal and says whether the boost you paid for is reaching the manifold.
  • 2D VE Table Generator. builds a baseline VE table, RPM against MAP, trimmed from your measured AFR or your fuel trims, in a CSV your tuning software can take. A clean starting grid, so the tune does not start from a blank sheet.

04 / A closer look

What the air tells you.

The Blower Drive Ratio and Air Demand calculator after a run, showing the estimated boost the pulley combination gives

02 / Blower

What will that pulley change give you?

Pulley sizes in, the drive ratio, the blower rpm at redline, and the estimated boost out, with the overspeed and heat warnings standing guard over the combination.

The 2D VE Table Generator showing the baseline VE table it built, RPM against MAP

03 / VE table

Where does the tune start?

The baseline VE table, RPM against MAP, built from your own numbers and trimmed from your measured AFR or your fuel trims, instead of a blank sheet.

Walkthrough

Watch all four tools run on one build.

The narrated walkthrough is below, running all four tools on one boosted build. The screens above are the tools themselves, run on real numbers.

The honest limits, stated plain: the turbo helper calls itself a sanity checker on its own screen. Real compressor maps depend on wheel trim, housing, exhaust backpressure, cam, and air temperature, and the final word belongs to a real map and the manufacturer’s data. The VE table is a baseline, a starting point, and the tool says that too. Real tuning still needs logs and common sense. These tools keep you out of the expensive mistakes. They do not tune the car.

05 / Delivery

Buy it. It is yours.

  1. Buy through My Access.

    Sign in or create a free My Access account. Stripe handles the secure checkout.

  2. Open the bundle.

    After payment, open it from My Access, signed in to your account.

  3. Keep using it.

    Open it through My Access whenever you need it. One payment, and it stays yours, no subscription.

06 / Questions

Before you pay.

Is this a subscription?

No. One payment. The four tools sit in your My Access account and you open them when you need them.

Turbo or blower, do I need both halves?

Most people run one. The bundle covers both because the air questions are the same questions: how much air, at what pressure ratio, at what cost in heat. The intercooler and VE tools earn their keep on either setup.

Will the VE table work with my tuning software?

It comes out as a CSV file, the plain table format tuning software takes in. It is a baseline grid to start from, not a finished tune.

What if it is not for me?

The refund terms are on the Terms of Sale and Refund Policy pages. The bundle invents no terms of its own.

07 / The price

One payment.
Yours to keep.

The first 100 founding buyers pay $39. After those 100 purchases, the one-time price is $69.

Founding price
$39
Regular price
$69

Boost & Air Bundle · $39 founding · $69 regular

Buy the Boost & Air Bundle

Secure checkout via Stripe through My Access. Tax is figured at checkout. You see the full total before you pay. Access granted after payment.

Also inside All-20 All-Access, the whole shelf in one purchase.

A free tool that runs alongside this bundle, free to everyone on the shelf: the Boost Airflow (CFM) Calculator.