Coil power feeds: where the coil's B+ comes from and why it can vanish under crank
The coil cannot fire on a promise. Learn where its B+ comes from - battery, fuse, switch, relay - why it can read fine with the key on and vanish under crank, and how a feed is proved in the condition it has to work in.
What the coil's B+ feed actually is
An ignition coil is a transformer that only works if its primary winding gets charged first, and charging takes current from the battery. The B+ feed is the supply side of that deal: battery power delivered to the coil's positive terminal. It is one of three separate jobs at the coil connector. B+ brings the power in, the ground (or the driver circuit) gives the current somewhere to go, and the command side decides exactly when the charge starts and stops. A fault on any one of the three stops the spark, and each one is proved on its own evidence - power at B+ says nothing about the ground or the command.
Where the B+ comes from: the chain
Coil B+ never comes straight from the battery. It travels a chain, and every link is a place it can be lost:
Battery and cables - the source. If the battery itself cannot hold voltage under load, nothing downstream can be judged until it can.
Fuse or fusible link - the protection. A fuse that reads fine with no current flowing can still drop voltage once real current crosses it.
Ignition switch or relay - the control. Many systems feed the coils through the ignition switch; many others use a relay (often called the ASD, main, or ignition relay) that the computer or the key pulls in. The switch and the relay are the two most common places a feed dies.
Ballast resistor or resistor wire - the limiter. Older points and early electronic systems deliberately drop the running voltage through a resistor or a special resistance wire. It is supposed to be there - bypassing it "to get more spark" cooks the coil.
Splices and connectors - the joints. Anywhere the harness splits one feed to several coils, corrosion at the splice starves everything downstream of it.
The exact chain is different on every vehicle. Service information - not habit - decides which links exist on the one in front of you.
Why the feed varies: key states and relay logic
Coil B+ does not behave the same in every key position, and the differences are by design:
Always-hot feeds - powered in every key position. Common on coil-on-plug systems where the computer handles all the switching on the ground side.
Switched feeds - powered only with the key on (and usually during crank). The classic ignition-switch-fed coil.
Relay-controlled feeds - powered only while the relay is pulled in. The relay needs its own coil power, ground, and command before the coil feed exists at all.
Crank-only quirks - some systems change the feed path during cranking (a bypass around the ballast resistor for hotter starting spark, or a switch contact that only makes in the CRANK position). A feed that is perfect with the key on can be wired to a different path - or to nothing - while the starter turns.
Test the feed in the key state the complaint lives in. Proving B+ with the key on proves nothing about B+ during crank if the path changes between the two.
What B+ presence is not
Two readings get confused constantly, and the confusion costs coils, modules, and afternoons:
Voltage with no load is not proof under load. A corroded connection can read a perfect 12 volts with the meter drawing microamps and drop half of it the moment the coil pulls real current. Voltage is only meaningful in the condition the circuit has to work in.
B+ present is not a working coil. Power at the terminal is one leg of three. The ground path and the command side each get their own proof - a coil with perfect B+ and a dead driver still makes no spark.
One coil's feed is not every coil's feed. On multi-coil systems the feeds split at splices. Proving B+ at one coil proves the chain up to the split - nothing past it.
Failure modes: how a feed vanishes under crank
These are the ways a feed that looks alive with the key on dies when the starter turns:
Resistive connections that only show under load - the classic. Corrosion, loose terminals, stretched connector pins, and tired splices add resistance that is invisible to an unloaded meter. Current times resistance is voltage lost (V=IR): at coil current, a fraction of an ohm steals volts the coil needed. The reading that catches it is taken during crank, not with the key sitting on.
Relay dropout during crank - the relay pulls in with the key on, then the voltage dip of cranking starves the relay's own coil and it lets go mid-crank. The feed does not sag - it switches off and back on. It looks like a dropout, and it is one, at the relay.
Ignition switch losing output in CRANK - the switch makes its RUN contact with the key on and is supposed to keep it (or make a separate CRANK contact) while starting. A worn switch can drop the coil output exactly when the key reaches CRANK - the one position the coil needs it most.
The shared path sags under the starter - the coil feed and the starter share the battery posts, the cable ends, and sometimes a stretch of distribution. When the starter pulls hundreds of amps, any weakness in that shared path drops voltage for everything on it, coils included. The coil's feed can be perfect and still starve because the common ground it stands on moved.
Fuse fatigue - a fuse element cracked but still touching reads continuity cold and opens under the heat and vibration of cranking, then cools and touches again. Intermittent, infuriating, and found by watching the feed during the failure, not by an ohmmeter on the bench.
How SpeedNeeds uses it
A coil feed is proved the way it works: presence first, at the live key state, with the meter on the actual terminal - then again under crank, with the battery's own crank performance proved separately so a sagging source is never blamed on the feed. The comparison that matters is the feed's own loss under load: what the source delivers versus what the coil receives, measured while the engine turns. A feed that holds its voltage under crank with the coil drawing current is proved; a feed that loses it is walked segment by segment - fuse, relay, switch, splice, connector - until the lossy link is found, and every repair is re-proved under crank before the case closes.
Backprobe the connector - never pierce the wire to measure. A pierced feed corrodes from the inside and becomes the next resistive fault.
The first fraction of a second of cranking is the starter's inrush - hundreds of amps that slam every shared connection. Judge the feed on the steady crank that follows, not the inrush spike.
A ballast resistor or resistor wire drops voltage on purpose. Know from service information whether the system you are testing is supposed to have one before calling the drop a fault.
Proving the feed does not prove the repair until the repair is re-proved. One disturbed connection at a time, then the crank test again - a fix that is not re-tested is a guess with a receipt.
An intermittent caught clean: a feed that holds voltage on a day the fault is hiding proves only that the fault is hiding. Note the conditions and measure again when the complaint is active.
Service information overrides every general rule here - feed architecture, key-state behavior, and expected voltages are vehicle-specific.
Closing clarity
The coil's B+ is a chain - battery, fuse, switch or relay, sometimes a resistor, always splices and connectors - and the chain is only as strong as its weakest link under load. A meter reading with the key on tests the chain at rest; the coil needs it tested at work, during crank, against a battery proved healthy on its own. Prove presence, prove it under load, walk what fails, and re-prove the repair. The spark starts at the feed - make sure the feed is really there when the engine turns.
Stay in the loop
Get new drops in your inbox
New QTS builds, tools, and garage stories — straight to your inbox. No spam. Unsubscribe anytime.